Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Take into account an application on the nRF51822 and S110.
I have defined different custom services, so UUID is 128bit long.
When advertising:
Is it advisable to include...
What are the mechanics of using 'uuids_more_available'? Is this list transmitted as a part of advertising data, scan response data, or both? How does the host know that this...
I'm using mbed+nRF51822+BLE_API+softdevice 7.1.0 for BLE peripheral side. I add uart service with the setting BLE_GAP_CONN_SEC_MODE_SET_OPEN which is open link, and set the...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi
While browsing the new files in the SDK 8.0.0 i had a look in the new ble_advertising module. In the start advertising function the pstorage access is checked if it's...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I have the nRF8001 plugged into the shield for the Arduino Uno.
From the Arduino SDK from Nordic, I have downloaded the BLE Hello World program to the Arduino, which should...
I know the SDK lists it for the S110 stack:
http://developer.nordicsemi.com/nRF51_SDK/doc/7.2.0/s110/html/a00066.html#app_dfu_intro_sec
But trying to use it with the...
There is a GitHub example:
https://github.com/NordicSemiconductor/nrf51-dfu-ble-S130
It states that the SDK 6.1 is required. Will it work with the 7.2 SDK using the...
I am trying to use TIMER1, but it seems that my ISR isn't being linked in during the build.
uint32_t timer1_init(void)
{
...
NVIC_SetPriority(TIMER1_IRQn, APP_IRQ_PRIORITY_LOW...
Hi,
I'm developing beacon-scanner software using nrf51822 and S120 softdevice.
Using softdevice v1.0.1.
I need to scan ibeacon type advertising devices and get service...
I am currently trying to come up with a viable strategy to log error codes that arise while my device is being used in the field. When an unexpected error code arises, I would...
Does someone use it?
The gls example from SDK 7.2.0 with softdevice 7.1.0 works.
However, the gls example from SDK 8.0.0 with softdevice 8.0.0 does not work.
I am using...
