Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hi team,
I'm using the NRF54L15DK board with NCS SDK v2.9.0.
I'm trying to include the B0 bootloader along with the MCUBOOT and application.
I'm wanted to customize...
As subject, the key is using prj.conf, compilation errors will occur, if do not use prj.conf, c ompilation pass but 54L15 not work(no logs aft pwer on). Is fast pair(locator...
Hi, I am currently migrating my project from nRF Connect SDK v2.5.3 to v2.9.0 / sysbuild.
Unfortunately, my devicetree configuration for a mcp2515 CAN interface is not accepted...
Hi, Nordic team
we want to develop indoor tracking system using nordic soc chip we saw some sample codes from your nordic sdk 2.9.0 , we need any research papers or documentation...
While experimenting with the v2.6.0 set of matter examples, it was noticed by an associate that the LightSwitch example doesn't seem to want to connect to any networks. This...
Hello, just like the title indicated, I need help with setting up the nRF21540 EK with the nRF9160 DK.
For my application, since the nRF9160 DK has the nRF52840 on it, I...
Sorry for the inconvenience!
I have downloaded V2.8.0 nRF SDK, and I use this command to build light bulb project:
west build -p always --build-dir nrf/samples/matter...
Hi everyone,
I’m working on a project involving the nRF7002DK, where I’m trying to combine two separately working applications:
A TinyML CIFAR-10 image classification...
I am attempting to configure and build the Asset Tracker v2 for my Actinius Icarus v2 board.but the build is failing.
Setup:
nRF Connect SDK v 2.9.0
Board target:...
Hi,
I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
Hi, Any one kindly suggest and Chip based antenna for the Thread + BLE and Wi-Fi + BLE protocol in NRF54L15 protocol. Also kindly suggest the PCB based antenna for the Thread...
In the past few months I got aware, that some, in my opinion simple questions, get marked with
"This comment is under review"
and then nothing happens. For weeks, even...
Hi all,
I'm doing some tests with the nRF5340 DK to log with a custom timestamp source. I took the logging exercise 2 example and verified that the log messages are correctly...
On the nRF54L15, how can I update the maximum TX time to 17040 µs when using Coded PHY?
I'm currently testing with the Throughput sample in nRF Connect SDK v2.9.1. During...
Hi there!
I'm in the process of updating our codebase from 2.4.0 to 2.6.4. We are using the nRF52840. My plan is to do this step-wise, following the migration guides for...
