Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
hello everyone ...I am working on a project that uses the nRF52840 IC. I would like to implement a power-down mode to reduce power consumption. In my project, I am using BLE...
HI Teams
I found in the datasheet that the UART, I2C, and SPI on the nRF5340 share the same set of IDs. Does this mean that these three buses cannot be used simultaneously...
Hi,
I'm trying to run the Lesson 4 Exercise 2 solution from the Nordic DevAcademy BLE Fudamentals course (origin/v2.9.0-v2.7.0) run on a nRF54L15 PDK board.
I'm currently...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi,
I am currently evaluating the Channel Sounding functionality for indoor localization. I would like to check how much Energy my Initiator and Reflector consume for...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello, I am currently developing on a custom board based on the nRF7002 + nRF5340. The SDK version is v2.8.0, and the development is based on the BLE Provisioning example...
Hello ,
I've been trying to build the wifi shell example sample for my nrf52840dk with a nrf7002ek shield. I'm setting the shield via CMakeLIsts ( set ( SHIELD nrf7002ek...
Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
Hi Nordic team,
My nRF52832 DK (PCA10040) was working perfectly until recently. Suddenly, it stopped getting detected by my PC.
Current Issue:
The board does not...
I am trying to follow the first lesson of https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals
But I have several problems and I can not find out how to fix...
Hi Team,
I am working on a project where we are using nRF5340/nRF52840 uC IC from Nordic. from past 2-3 years we were using this software hassle free but now due to to some...
I am using NCS 2.9.0 and latest extensions for VS Code.
To reproduce, use Mac, create a new app from Blinky sample, build it and open "prj.conf", then wait a few minutes...
