hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Title
nRF5340 DK × 2 + MCP2515/TJA1050 – can_start() = -5 (CANCTRL/CANSTAT = 0xFF). What am I missing?
Hi everyone,
I’m trying to bring-up a very small CAN bus test...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I have tried in various ways to make the XIP part functional on SDK version 3.0 (SDK v3.0.0-3bfc46578e42) but without success, this on the NRF5340 devkit. I mention...
Hello nordic team!
Context:
Currently I am working on modifying our application code to be able to select, at runtime, which network interface it will use (between ethernet...
I have an application that syncs via the internet using a nRF5340 and nRF7002. I am using the thingy53 with a nRF7002EB for now while the custom circuit boards are being manufactured...
Hi,
am working on nrf52840 withst7789v custom display . I have integrated the my display code using lvgl library with PMIC code in zephyr . while doing that I have configure...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Does nRF9160 support IoT devices, SGP.31 eSIM IoT Architecture and Requirements for remote provisioning of eUICCs in Network Constrained and/or User Interface (UI) Constrained...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
I have the following pm_static.yml configuration:
and I'm trying to acces this `custom_bootloader_header` from my application code. Here's the relevant snippet:
...
Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Hi all I am new to Nordic world. I have received a nRF5340 audio dk board and would like to be able to get VS code to build the default sample code - I have tried in windows...
