Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Hi,
I use the nrf24le1 device in my design. I want to stroe data when power is off, so I write data to the NVM flash. But something is wrong in my design, could you help...
Hello,
I am using the nRF51 transmitter_pca10028 example to try to communicate with legacy systems using nRF2401A.
I could achieve nRF51 TX to nRF24 RX successfully...
I would like to burst out 12 packets of 64 bytes and then go into RX mode immediately after for a single payload, followed by another round of transmissions. Is there a shortcut...
The data is sampled at 3khz, each sample is 2 bytes, connection interval is 7.5ms ,4packets per connection interval. The data is displayed on a graph with respect to time...
When I execute nRF5x_MDK_8_7_1_IAR.msi from the SDK 11 directory the files from the .msi are added to the IAR install directory, not the SDK. These changes are ignored when...
I was little bit confused between NRF24l01 and (+) plus version which is better . i want range of 900-1000m. which is best??
If i choose NRF24l01+ what are the ways to...
(/attachment/0495424521df76d5b8f8e66c969ed791)Hi,
I add ANCS Service into my Heart rate ref ble_app_ancs_c example code.
I use MCU nRF51 and SD130 in nRF5_SDK_11.0.0_89a8197...
Hello,
My device is based on nRF51822 SD110 v8.0. Softdevice is enabled, but no BT functionality used. I measure 2 different voltages with ADC each second with two channels...
I'm writing code for PCA10040 basing on UART/NUS example. There are no big changes: different UUIDs and just one characteristic for both reading and writing. I can connect...
This is a follow-up question from devzone.nordicsemi.com/.../
I finally got passkey support to work on ble_app_uart but don't quite understand the changes made to the code...
I am trying to add static passkey pairing to ble_app_uart in SDK_11 s130. To do this, I first implemented static passkey successfully in ble_app_gls using sd_ble_opt_set(...
Tl; dr
I tried to use OTA DFU with Public BLE Address, but I failed. Is this possible?
Details
Condition
I modified ble_app_hrs example like below (SDK11, pca10028...
I have a radio board using a NRF51822 with a custom radio protocol. I need a unique identifier, ideally 24bit, 32bit but be acceptable.
I notice in the parameters there...
I've looking through as much of the documentation I as I could to read more about the radio timeslot api.
I looked through the SDS document and the chapter on the Radio Timeslot...
