Hi, I want to implement a feature where the central device manually enters a fixed password (passkey) defined by the peripheral to establish a connection. I’m using the ble_app_hrs...
Hi,
I send "chat private 0x0028 hi" over a serial terminal, and the MCU restart because of overflow, please see error log as below picture.
I tried to modify the "CONFIG_SHELL_STACK_SIZE...
Hi,
I'm using thingy91 for several weeks now and wanted to erase everything to start again from a clean basis.
I followed the guide https://docs.nordicsemi.com/bundle...
Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
When I was using the code from the following website, I encountered many errors while creating a new build for compilation。
https://github.com/NordicPlayground/nrf-esl-bluetooth...
Hi Team,
I have added the NUS function in the Matter project. After the commissioning broadcast is turned off, NUS broadcast will automatically start. I want to manually...
Hi everyone,
just a quick tip that may save you some debugging time when using the nRF Connect SDK Build Configuration Editor (both in VS Code and standalone):
If you...
Hello.
I have adquired PCA10028. I use IAR IDE. I have downloaded an application example for the nrf51422 using the JLINK hardware of the PCA10028 board. I can download...
Dear All,
any opinion on attached antenna design (blue) to the outside of a metal housing?
PCB that flows around an aluminium die cast housing
External to aluminium...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi all,
I cannot find the exact connector to use for the P19 Debug out header on the pca10028 board.
The one I have has the plastic around too big so it doesn't fit.
...
Hi,
I'm working on a simple ADC application where I sample using analog channel 1 and then read the value through the debugger. However my results are nonsense. I have...
I'm using s120_nrf51_ble_driver on PC.
To connect the BLE dongle, we need to COM port number to be known (parameter of sd_rpc_serial_port_name_set). Is there really no...
I am working on a project on wireless interface between phone and SIM card. I want to use chip nRF51822-CEAA to run SIM card simulation at phone side (include wireless communication...
in nRF51822 product specification a maximum absolute rating of 3.9 Volt is reported, while in electrical specification the maximum voltage is 3.6 Volt.
The question is :...
Hi,
I have tried with the nrfjprog tool and I get the following error:
Command:
nrfjprog.exe --eraseall --programs s110_nrf51822_7.1.0_softdevice.hex --program HILO_P_01...
Am trying to setup a module where I need to send the Serial port ( say from printer/peripheral COM)
to a BLE Peripheral/Central Module. Not sure which SOC or combination...
I have a board built which is a tracking device with a GPS and GSM modem. I'm beginning field testing and have been flashing it with a Segger then disconnecting the Segger...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
I have an nRF51822 board that is running fine for a while. At some point, it runs into an error and calls ble_debug_assert_handler() and goes into an infinite loop. At that...
