To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
How can I advertise a custom service and the Device Information Service?
I tried the following, but only my custom service is visible in the Nordic Master Control panel...
Hi there,
I'm issuing a STOPRX at a specific time but I'm noticing that more bytes are being put into the buffer from after the STOPRX was issued.
Is there a way to...
Since I've migrated to SDK 10 and updated all my toolchains I've noticed that when I debug on Eclipse, when I run my code nothing happens properly. However if I pause and...
There are various examples in the keil microvision examples for DTM.
The list is below. Is there a difference between these examples?
Which one should we use if our design...
Currently the default for the SPI0 chip select is active low. I would like to change it to active high. Can I do this?
If not can I just have the SPI chip select on a pin...
Continuing with my attempts to get this to work on SES I'm not sure if I'm missing something simple or not.
So using the excellent RKNRFGO (which by the way is much quicker...
There is an error in the gcc makefile included with SDK 5.2.0 that prevents it from detecting when a header file has changed and automatically recompiling the C files that...
Hi all,
I've always been a CSR developer and recently been asked to develop on the Nordic chip. The example code makes sense to me and its not to different to the CSR code...
Hello,
I have a custom board and I am trying to verify the maximum throughput on NRF51822. I am able to communicate with Android BLE stack, however, I need to increase...
Hello! :)
I am a beginner with micro controller programming and want to start with a nrf52
Could someone please explain the difference between the development kit...
Hi,
we have a project in which we have to scan a lot of beacons (up to 100) with Active Scan (scan request and response). We tried to implement this system with actually...
There's an example saadc_pca10036 in the SDK. I am wondering how this piece of code works in that example:
void saadc_init(void)
{
ret_code_t err_code;
nrf_saadc_channel_config_t...
I am working in the SDK10.0 ble_app_uart_c(master),it can connect to ble_app_hrs(slave) successfully.
But if I add a new 128 bit UUID named ACC_BASE_UUID different from NUS_BASE_UUID...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_multilink_central" for reference.
Multi-connection function is OK.
Whenever I connect to peripherals, I can see connected...
