Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I am running ble_uart_app in SDK_11 s130 on nRF51-dk
I am trying to detect certain pattern received in the UART Rx.
Here is my code.
void uart_event_handle(app_uart_evt_t...
I'm running SPI master (spi_master_tx_rx) at 4MHz for multi byte burst reads. As seen in the attached screenshot there are 5.5µs delays between the bytes. The delays increase...
hello there ,I am writing spi code for slave which has 19 bytes of data. my nrf51 is master.
now my slave has clock polarity =1, clock phase =1. i am uploading project...
Hi All,
I'm trying to test the ble_app_hrs_rscs_relay example on an nRF51822 (256 Ko flash / 16 Ko RAM) with the softdevice s130 but unfortunately the program is not being...
I am using ble_uart_app on SDK_11 nRF51-dk s130.
I would like to send binary hex data instead of ASCII. Looking at ble_nus_string_send(), it seems that sending binary hex...
Hi ,
Recently started working on nRF52832 and tried implementing its various applications for NFC, which includes URL, android application, name tags. Can anyone suggest...
As part of some testing, I downloaded some wrong files and seem to have contaminated the default boot files. So now when I try to download the NORDIC hex files, i get an error...
Hi ,
We are using NRF52, S132 softdevice ... Whenever we do hard reset everything works fine .. But if I do flash from my IDE (using eclipse,this is a soft reset) and it...
I have a hard time to initial a twi ,I reference the example in the SDK11.0，and I used the board is 10040,I copy the example twi sensor code in my project ,but there is an...
I'm getting the error code 0x4001 from sd_clock_hfclk_request and I can't find where the error codes are defined/explained for this function. Can someone point me in the right...
Hi,
With the following program running, how can I achieve the lowest power consumption between timer events:
nRF Timer is running with the HF crystal requested
...
51822, config a pin as output , in the param , set disconnect or connect the input pin, when config as output ,what mean disconnct/connect input pin?
I use a pin to light...
For my project to simulate the spreading of a disease I am thinking of recording the complete social network on the beacons and then collecting the data to a pc. I have roughly...
I am using nRF51-DK hardware and working on the ble_uart_app s130 SDK_11
Upon power-up, nRF51 is discoverable and connectable. After sometime, it is no longer discoverable...
