Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi.
I want to make a device which can connect each others and communicate with NUS.
I need not to use any other service without NUS.
I made nus_c service which is a central...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
Hi!
I want to connect a nrf51 dk with a beacon and I'm using the UUID to make the connection. In the beacon code I define the UUID in this way:
ble_uuid_t adv_uuids...
I use nrf52832 with softdevice s132_nrf52_1.0.0-3.alpha for a ble application on own pcb.
first I'm not sur of adresse to use for iROM and iRAM areas. I've this parameters...
//Hi Everyone!
//I am programming a nRF52832 through the SDW interface and am having trouble answering some questions.
//So, first off is simply checking my understanding...
I have a recent dev board and am using SDK11 with gcc.
I can build and flash OK
The blinky sketch runs
However, when I load up examples/ble_peripheral/ble_app_proximity...
We bought the Beacon Kit from Nordic. I'm trying to use the firmware code on a similiar beacon board based on same Nordic Nrf51822. The board has same button and led pins...
The release notes for the S132 V2.0.0.0 SoftDevice indicate it's only compatible with silicon revisions C and 1.
I have several PCBAs that have the rev B silicon. Will...
Hi guys
First of all, I know nRFgo can be very convenient for application encryption, but in order to improve the mass production efficiency,I merged the application code...
Hi!
Goal: I want to send as much data as possible using CoAP.
I have connected a nRF52 (IoT-DK) to a Raspberry Pi using BLE and 6LoWPAN. The nRF52 is running the CoAP...
I use the nrf52832 with softdevice S132 s132_nrf52_1.0.0-3.alpha for a ble application.
without the softdevice, the rtos works correctly.
but when I enter this parameters...
I'm moving from nrf51 to a higher performance uC. I think that there is lot of models of nrf52.
what's the reference of the best nrf52 in term of performance. I want to...
I've been using the device firmware update service for quite some time now. I'm looking to add the ble_nus service, but this feature seems to fail when ble_dfus is re-enabled...
With the latest nrfjprog from Nordic and latest J-Link software from Segger, I am still getting the error below.
$ nrfjprog -v
ERROR: JLinkARM DLL version used is too...
I am working on the ble mesh using nrf51822. I am able to read the mesh values using the nrf master control panel android software. But we want to make an android software...
