Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hello,
I am working with the nRF52 dev Board and the question arose whether it is possible to interface the nRF52 chip via the virtual com port?
The block diagram in...
Hi, I have problem when change S132 V2.0 to V3.0.
SDK : nRF5_SDK_11.0.0_89a8197
I download s132_nrf52_3.0.0.zip and replace all files in nRF5_SDK_11\components...
I want to know if it is normal to have different hex files after compiling the same project from each one in a different PCs using the same IDE Keil ?
That's really strange...
Hello all:
I am running a nRF52832QF AAB0 pca10040 board with SDK11 in Segger embedded studio.
I followed the 'getting started' tutorial.
After pressing button 1, I noticed...
Hi
is there a possibility to make nrf.exe work under OSX? Is my understanding correct that it is actually written in python, hence, should be portable to mac osx or linux...
With softdevice version 2.0.0, the sd_ble_gap_address_set is used to set the address to one of the four address types, and sd_ble_gap_address_get is used to get our own current...
Hi
Sometimes the nrf the central does not accept my connection interval of 7.5ms. I want to disconnect nrf51822 when the correct connection interval is not negotiated with...
I'm in the process of integrating the DFU features in our application. I am using the following tutorial as guidance (the section is called "Including DFU files in your application...
I am trying to port the experimental_ble_app_multiactivity_beacon advertiser example to nRF52.
I have used the document 'Migrating an nRF51 BLE project to nRF52' ( infocenter...
Hi,
we recently moved from the nrf52 DK to a custom board. We went from 2uA current consumption in sleep to 500uA with the custom board. The main difference is that the...
I have been trying to adapt the following example project to work with my SPI peripheral device (LIS2DE12 Accelerometer):
nRF5_SDK_11.0.0_89a8197\examples\peripheral\spi...
I am trying to implement SCCD on S130 v2 sdk11 but this is not in the scope of the tutorial.
I have populated the structure just the same as for CCCD, but I can't have the...
I need to read / write data over RTT with an nRF52 target device. There are function prototypes in nrf52_nrfjprogdll.h that look like what I need.
Before I spend the time...
Hi, I want to connect to a simple Bluetooth device with the help of NFC, no pairing shall be performed. In short, I just want to get the MAC address of the Bluetooth device...
