Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Good day, I was attempting to test the radio performance of the NRF54L15. I ported over the Radio_Test sample project to try and transmit an unmodulated carrier wave at a...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Hello.
How often are the LQI and RSSI values in the coordinator updated for a child?
Preferably I would have liked to get some kind of notification every time LQI and...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hi Nordic team,
I’ve been working with the nrf_dm sample from NCS 2.9 to perform distance measurements using multiple nRF52840 devices. The sample works well, and I've made...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hey guys!
I am using your spi-master driver from the SDK 11 with the nRF52 chip. I am trying to read data from a MPU-9250 chip, and through my logic analysis, it seems...
Hi to all!
I've developed a board with NRF8001 on it and it works fine. But I've noticed a strange behavior. I use a mobile phone with NRF master control panel to work...
Dear All,
I am making IR transmitter using nrf51 where IR codes saved in SD card using PWM library we can transmitt the code while BLE is working.
Is it possible that...
Hi,
I am working on some application in which i have combined multiple profiles in one code.
In this i don't want generic access and generic attribute profiles to be displayed...
Hello.
I am using RTT successfully with nrf52 and IAR. But the start address for the RTT control block is a moving target: it changes whenever my code changes. I want to...
The product specifications publication for the nRF51822 doesn't list a gull wing chip pinouts found on the PCA10028 found on the evaluation board, kinda wondering if there...
Can someone confirm that all that needs to be changed to make code run with the SD installed is to change the linker to link to 0x1C000 instead of 0x00000 ?
To test, I...
I am playing with nrf51 DK. I used the following sample code,
devzone.nordicsemi.com/.../
ble_app_template_with_pstorage_SDK_8_1_0.zip
I want to pstorage clear/store...
I'm having an issue with secure BLE pairing, and once the problem shows up, it will not go away until I reprogram the SoftDevice. It persists through resets, so it must be...
I am currently using the nrf52 device for an application where when user's of my devices come close to one another, they automatically start sharing state information. There...
Hello all,
I currently have a test rig with 3 sensors, each with their own pin and interrupt they are supposed to carry out. Whichever two I put first in my gpiote_init...
Dear all,
I'm using SDk130 and the Software is based on the ble_app_uart_c example.
Now I want to scan the advertising data from a peripheral (device name, peer address...
Hi all,
Will the Gazell protocol be available on the nRF52, or should I stick to an nRF51?
Also for a new product, is it better to use Gazell than ESB?
Thanks!
I am new to android studio. I downloaded git hup zip folder and also dfu folder. I unziped both in a same folder.
I opened the extracted folder using android studio. But...