Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi,
I think there is the bug in SDK11 Spi slave protocol. After a msg is received from the SPI Master, I notice that the spi slave event always have the rx_amount and tx_amount...
Hi All,
I noticed these serialization FW with huge amounts of code in the makefile.
What is the core functional difference between any example with and without serialization...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
When I write 0x0104 to DFU control point characteristic, my device is switches...
I am trying to use the ECB encryption mechanism and had it working perfectly well on the 11.0.0 alpha SDK. With the release of 11.0.0 it now hardfaults ( NRF_ECB->TASKS_STARTECB...
how do I modify antenna of nrf24l01+ by connecting external smt antenna to it? for this purpose I need rf ground and antenna core, I can't find rf gnd here. is that same as...
Hello,
I need a solution to scan for BLE devices and read device characteristics database through UART on PC (Win). Something like Master Control Panel, but a cmd line...
Hey,
I have a problem with sending data on Notification. The problem is data is transmitted in the characteristics even when the notification is not enabled by the app.
...
Hello I am happy to you to read this text...
I meet a problem...
when I want to work nrf51_SDK_10.0.0/example/peripheral/blinky/pca10028
so i clicked "Rebuild" but...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi all,
I would like to setup a system where a single central BLE device (a smartphone) has to talk sequentially to several BLE perihperals (Nordic chips).
I need to...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I made timer(repeated) as below.
void init_timer(void)
{
uint32_t err_code;
err_code = app_timer_create(&m_timer_id,
APP_TIMER_MODE_REPEATED...
Hi,
I have a nrf51-DK, and I use softdevice s130_1.0.0 with keil c 5.18a,
My project with custom service uuid "DFU" and custom uuid "my_uuid", and battery uuid, alert...
Hi,
I've noticed that in the examples that come with nRF5 SDK11 there is a template for creating BLE peripherals (ble_app_template). I was wondering if a similar example...