It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
A general question, not really related to Nordic, but...
I have seen several references to BT 4.0 headphones. I was under the impression that BT 4.0 didn't have a profile...
I am trying to disable rx after starting data transmission, is there any way to do this for ble projects, and is there any advantages in terms of lower power consumption?
txidle.png
In the attachment there is a method to reduce delay while transmissiom. Do you think this can help lower the power consumption? If so how can we do this using...
Hi,
In pstorage.c, function uint32_t pstorage_init(void), there a call to sd_flash_page_erase (line 846):
// Erase swap region in case it is dirty.
retval = sd_flash_page_erase...
Hello,
I'm curious about how to deploy my application to multiple nRF51 Dongles at the same time while I am developing. I have the same application / hex file running on...
Hi,
I'm trying to connect my nRF51822 PCA100001 development board to a ARM M3 processor via the SPI. In this case the ARM M3 is the SPI master and the nRF51822 is the SPI...
Hi,
I am having a nRF51 DK(PCA10028) development kit. I am trying to run blinky example on this development kit using Eclipse+GCC environment. I am following nAN-29 application...
Hi, I'm trying to locate the Softdevice whitepaper (nWP-20), the S210 softdevice specification makes reference to it, but I can't seem to locate it anywhere on the nordic...
Hello Everyone ,
I want to use pstorage for my project.i get the example code from here
devzone.nordicsemi.com/.../
and its working properly(i.e read and write operation...
I am using nrf51822, after establishing connection between master and slave, circuit needs only tx antenna, is there any way to put rx in sleep mode for ble application? During...
I have some nRF51822 MBED kits and I want to use them for BLE for both peripheral and central roles. I understand that this is possible with the S130 SD and the Nordic SDK...
Hi, this question could be ridiculous question due to my lack of data structure knowledge.
As you see in the HID keyboard example (SDK 7.2), there are several buffers....
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...