Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I can get an information that bluetooth smart connects bluetooth smart ready.
But I can't get an information that bluetooth smart connect bluetooth smart ready.
So, Would...
I am using nrf51822 and i want to run my application using softdevice.
But I am not able to start my softdevice Please can anyone guide me how to start my softdevice.
I...
How to enable the notifications or indications? In APP? can I enable it in ble peripheral?
I meet a chip of "Quintic" can do this. When I connect it to MCP and I get this...
I made Pwm program with 3 channels without using softdevice and without using interrupts at that time it is working perfectly. But when i am trying to use softdevice with...
Sometimes I receive pipe error 0x92 when I try to send a message from nordic to Android. What could be the causes for a pipe error 0x92?
I saw this: "Pipe Error Event ...
Hi,
I purchased nRF24Lu+ modules on ebay. I am trying to talk to them over USB from a linux machine.
Nordic datasheet states:
VID = 0x1915 and
PID = 0x0101
When...
Am I right in thinking that these security parameters are contradictory in that for the peripheral (nRF51822) to provide MITM protection, there must be either IO capabilities...
I just received my nrf51822 and am using an-36 as a starting point to build my first "Hello World" application for BLE.
All I would like to test is to have the status of...
I am trying to only perform calculations for connected ble services.
I am implementing a state machine that monitors the ble evt.
I use this for example when to perform...
hi guys,
I add a temperature service with one characteristic to notify the IC temperature in hrs example. But when enable hrs notify, SoftDevice crashed every time. That...
Hello,
We are using SDS 6.0.0, SDK 5.2.0 on an nRF51822. Our application is a data logger that can collect up to 128Kbytes of data. Users can connect to the data logger...
We did set the perform bonding option in the proximity example in the v6.0.0 sdk to 0.
And it did work. No bonding information is stored. Android devices are fully capable...
