I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
Does anybody know what I could be doing wrong either on peripheral or PC when my program on PC reports this error?
I am in the process of writing an application...
Good morning. Thanks for reading. I am brand new to development on Nordic platform but fairly experienced with ARM Cortex, GCC, IAR, Eclipse, etc.
I have a the PCA10003...
Hey guys. I'm very new to Bluetooth 4.0 (actually Bluetooth in general), but I'm hoping to be able to use a Fujitsu MBH7BLZ02-109004 module with an nRF51822 in a product I...
I am attempting to measure battery voltage through the ADC, but am getting inaccurate results. In my setup, I have a 4.2 V battery divided down to the bandgap range using...
HI all:
I am using the nrf24le1.And i confuse about the recive and transmission address in rf transceiver.
What do we use the address to do usually.It will be wonderful...
Copy nrf51.cdb to "C:\Keil\UV4"
Copy nrf51xxx.flm to "C:\Keil\ARM\Flash"
Set the keil project-device to nRF51822(data base : Nordic nRF Series Devices)
This is...
Hi
Is there a documentation of the nRF51822 sniffer interface? e.g. communication structure, command format, captured messages structure etc?
Thanks
Yaron
I'm trying to set up a network where 1 - 4 BLE devices wirelessly talk to a computer. I'm using an arduino connected to the BLE shield.
The computer is a Winows 7 laptop...
Hi,
I'm creating a project on nRF51822 chip and I have a problem with disconnection. In my program I want to disconnect with master after some time e.g. 30 seconds. I'm using...
I'm unable to write my application code to the flash of an NRF51922 (QFAACAA). NRF Studio will let me flash the hex file but it fails verification. If I try programming in...
I have a question, can nRF51822 operate in regular Bluetooth mode like a Bluetooth 2.1 device?
If answer is no then, is there any product from Nordic that operate as Classic...
Hi developers,
I've finally got the nrf51822 working and advertising a good signal to the dongle. :)
After doing all the steps in the NAN-36 pdf-file I hoped that pressing...
Hi all,
I'm using Timer2 while having the SD enabled, and I'm having some problems. I don't seem to be able to reliably set the periodicity of the timer. No matter what I...
I've spent quite a while getting Eclipse on Mac OSX working. I started with the original makefile but have come up with, finally, a working native Eclipse build which does...
Hi all,
I have an external dongle (Bluegiga) that is scanning for BLE devices.
My problem is this: all the BLE devices in my room are showed correctly except my nRF51822...
