I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello,
I've checked the timing diagrams for the CE and IRQ on the datasheet but I would like to know if anyone has actually tested them with an oscilloscope? If yes could...
I am using SDK 11.0.0 on a nrf52832, with FreeRTOS and SD132 2.0.0. I configure the FreeRTOS port so that it uses RTC1 as SysTick. Depending on some compilation macros, my...
Assuming that all peripherals that require the high frequency clock are disabled / turned off / stopped, how long does the HFINT oscillator run after calling __WFI()?
And...
What's the delay from setting the Start / Stop task in an RTC module to when the RTC actually starts or stops? Is it less than 1 clock cycle on the CPU (15ns)? More than one...
Hi, I am using the nrf52 dk to sample two analog inputs through PPI.
My question is if I can use different bit resolutions for each analog input?
-Erblin
Hello !
I have a problem with my program (on a nRF52 board) : when I send a value to the board via BLE, it seems that my static variables are reset.
I noticed that, because...
I need to store data in some moments and if something happen i have to read those data, i have to do a log events.
I use nrf51-dk and soft device s130. This data is taken...
"....\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production. Please see github.com/NordicSemiconducto.. . to generate it.
i found...
nrf51 dk with 51422 device (10028) was running in Segger Embedded Studio example imported from IAR / Keil ble_app_cscs_pca10028_s130 SDK12.1.0 was just fine. I loaded couple...
Hi,
I'm new and I'm a student.
I have to connect the adxl345z to my board mb39c811-evbsk-02.
It has an nrf51822 integrated.
Someone can explain which pin of i2c/Gpio i...
We wanted to update the firmware over the air, We needed help for zip file creation(.dat file, .bin file and .json file). There are many links online, We needed an link which...
Hi,
I'm developing to NRF81522 mcu, using a softdevice S130.
The MCU is connected to another device through the UART peripheral.
I'm encountering the next problems...
Hi,
I am getting data from sensor and want to replace some new data with the older one in flash using fds. Right now,firstly i will write into flash by using one different...
I am using the nRF toolbox to upload bootloader and firmware to a hardware project. Our project requires the number of packets (found within settings > nRF toolbox > Number...
