Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
We did initial work on the NRF51DK (PCA_10028).
We are using SDK 12 and ARM-GCC.
We were able to compile and run successfully the experimental_ble_app_blinky and connect...
I'm attempting to make a sense of app_gpiote.c (in SDK 11) to see if it's suitable for my application and I can't find a match between the documentation, the sample code and...
Hi,
I am trying to use app_timer (had this working in isolation like I wanted) and esb (also had this working by itself) in the same binary. They both implement SWI0_IRQHandler...
Using nRF51822.
I use external DCDC to supply concurrent 3.1V for VDD(PIN1).
Then I have no way to check bettery level.
So I connect battery and AIN4(p0.03) separately...
Hi,
This seems to be an issue that pops up often. However, I wasn't able to find an answer here in the Nordic forum.
What I have:
a number of vendor services ...
I'm trying to change the SD version number of a test-S132-file, soI can "see" that the DFU was successful in my app. I can already read the current version (from 0x300C in...
Does anyone had controlled LoRa module with nRF5x??
I have nRF51822(BLE400(PCA10001)), nRF52832(PCA10040) and Semtch SX1276RF1JAS.
I hope to control LoRa module using nRF...
Hello All,
I am looking for a stand alone small transmitter/receiver that can be powered from a watch battery with a range of at least 300m. Is any of the nordic solutions...
hi,
i am working on code which require to store data array of 20x20 to store in flash area using FDS or any other possibilities.
1)i confused with FDS concept. how i can...
Hi,
we are now in the second round of prototyping - we'd like to move away from the chip-antenna based design to a PCB antenna. We have come up with two different ideas...
Here
My device (chip nrf51822_xxAA) exist softdevice 8.0.3 and BLE uart application work fine which flash by the ST-link in Keil MDK(5.20).
Now I try to add bootloader to...
Hello
I've found your example in the dev-zone and migrate the project to SDK10 and will probably do the same for SDK11.
However, I've got a problem in my project. When...
hi,
i want to implement rtxos in my nrf52832 application. one of the nrf52832's feature is ARM Cortex -M4 32-bit processor with FPU, 64 MHz.
my question is, why the...
Dear Nordic.
I am developing bootloader without SD (s120_nrf51822_1.0.1).
And after execution of bootloader, jump to application working with SD.
Flash composed like...
I tried to compile blinky sample in SDK12 with make tool-chain. I got 3 errors:
Makefile:214: Cannot find include folder: ../../../config/blinky_pca10040_s132
Makefile...
