hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello.
I use the BLE multilink central example to connect to 2 sensors. I changed the example in that way that i successfully connect and read data from a Wahoo Cadence...
the application is examples\peripheral\csense , cap sensor can sense my touch, but when I cover a 1mm acrylic on the cap sensor, will not sense my touch.
so I want to know...
Hi ,
We are using BLE nano board as a connectivity board and mDot board as application chip which is running on mbed platform.Connection deatsils are same as described here...
Hi,
I am working in one application in which I need SAADC to sample two channels at 1ksps and 500 samples per seconds.
I am sending 1 and 2 to switch the sampling rate...
After trying to run keil project after setting conditional breakpoit it raises error.
is it right that nrf52 doesn't support conditional breakpoits? or something wrong...
Hi,
I'm using the SDK11 and SD130 on a custom board which has a nrf51822.
I connected via SPI to a DSP that sends and receive audio.
My handler of the SPI is as it follows...
I'm trying to send a set of 246 bytes by uart fifo. I have a PC side which retreive the data, but I always miss some bytes (4 to 6).
I'm checking app_uart_put return and...
Hello,
I would like to use the nrf51822xxaa as BLE gateway for an ARM application processor (connected through the UART).
I successfully cross-compiled pc-ble-driver...
Hi..
Can i use both observer and broadcaster roles concurrently in s130 soft device..?
Is any TDMA needed to do this..?
Is it possible to do without stooping the other...
Hi,
I have read the S132 Softdevice specification v3.0 and just want to make sure that my interpretation is correct. There are two scenarios I would like to verify:
...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
When...
Hi,
As a beginner, I'm trying to have CDC J-Link Uart port work with my laptop. I'm using nRF52 board. When connecting the board to my laptop (windows 10), it displays...
Need some help on the tcp server example in the IoT SDK.
All steps working but the python script gets Connection refused.
bash# ifconfig bt0
bt0 Link encap:UNSPEC...
(nrf52832 PCA10040)
Hello. I'm trying to go along with the ble tutorial (advertising, service).
I download before last version of sdk 11 because with last 12 it's not working...
Hello everyone,
I have 2 chip; Bluegiga and nRF51-DK
I can easily advertise my custom service in Bluegiga chip. As you can see, nRF Connect application shows my service...
