Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Dear Folks,
I have a question regarding the supply rise time of the nRF52-Series.
According to the Product Specification Chapter 6 Table 8 the Supply rise time (0 V...
Hi, I encountered some problem using the S132v3.
With the s132 v3 and sdk12, I want to extend the ble transfer size.
Now I can change the att_mtu to 100, and iphone...
Hi all!
I recently ordered BLE tag with nrf51822 QFAB chips.
When I read back the memory content (with mem8 jlink command) I manage to read up to the address 24A60 which...
The task I am working on is sending a list of records from an nRF52832 chip to a central. Before sending the records, the total number of them should be sent, so the central...
Hello. I'd like to know. Can I trust to opportunite to firmware my controller (nrf52832) over the air. I mean is there any chance do not be able to do it, for example if last...
I'm using a module that has nRF24L01 mounted.
When I transmit to many PRXs, using the same frequency and channel, I expect to receive
many ACK signal at the same time.
...
I'm using nRF24L01 in a star network and i want to disable ACK.
I write the ACTIVATE command followed by 0x73, then a write to register FEATURE the value 0x01.
In this way...
I am trying to follow the tutorial given on this page:
devzone.nordicsemi.com/.../
However, my eclipse project does not build and created following log
13:55:03 ...
app_pwm_uninit is hanging the code. The control goes to pwm_dealloc() and then in nrf_drv_ppi_channel_free() it hangs.
Using SDK10. I want to change the PWM frequency and...
I am new to eclipse IDE and I am following tutorial on this page:
devzone.nordicsemi.com/.../
I am able to make the blinky project on the terminal and it does create...
Hi,
I have the following piece of code.
nrf_gpio_cfg_output(PIN_EN_BSTR);
for(int i=0;i<300;i++)
{
nrf_gpio_pin_clear(PIN_EN_BSTR);
__NOP();
__NOP();...
Hi,
I’m trying to use new SKD 12 secured bootloader but can’t pass signature check in dfu_req_handling.c\dfu_handle_prevalidate() (code after switch case DFU_SIGNATURE_TYPE_ECDSA_P256_SHA256...
Per table 19.4.2 in the nRF52 PS v 1.1:
, what is the difference between CL (load cap) and C0 (shunt cap)? The max ESR is specified for C0 but not CL. The xtal datasheets...
I'm looking for an nRF52 development kit with the PCA10040 1.1.0 or 1.1.1 board and the revision 1 IC . Closest I can find is that SemiconductorStore (Symmetry) claims theirs...
