Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Can anyone point me to sample code that exercises ANT's "advanced" burst mode? I have sample code provided by the Keil SDK that contains a prototype for function sd_ant_adv_burst_config_set...
I'm actually writing some data to the flash. I'm using pstorage api interface.
But whenever I flash the new firmware, I get some garbage data.
in my main function I would...
Posting this question here as there seems to be no Tech Support available in India.
I am looking for a BTLE solution that can be used in my BT device.
The functions...
My Problem
ble_app_uart app hangs at main.c line 503 " ble_stack_init(); "
My Setup:
SDK: nRF51_SDK_8.0.0_5fc2c3a
Device: nRF51 DK
Editor: CrossWorks
...
Hello development zone,
I'm new to nordic, and I have a question about role swithcing.
With knowing that, this kind of questions may be answered many times before only in...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
hello everyone
I have some questions with the following function in the hal_aci_tl.cpp file
static bool m_aci_spi_transfer(hal_aci_data_t * data_to_send, hal_aci_data_t...
Throughout twi_hw_master.c, there are lots of places where the code directly accesses PPI channel #0 and thus assumes it's available, as in:
NRF_PPI->CH[0].TEP = (uint32_t...
Hello, I have built a couple of custom boards in the past using the nRF51822 and have stuck very closely to the reference designs. They have all worked.
In my latest board...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello,
I successfully flashed the experimental_ble_app_uart, I just modified it to do an echo (when I send something with my phone uart app, it give me back the same value...
Since related topic Is BLE changing licensing policy? was marked as resolved I moved my question to new one.
My company is ready to get SIG membership for BLE usage and pay...
I'm creating a custom beacon, similar to iBeacon, but with a custom data format. It advertises only once every 8 seconds, but the iPhone app doesn't receive advertisements...
