Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I'm getting the following notice/warning/error when building my application (nrfsdk 2.9.0 w/ sysbuild, nrf9151dk board):
/usr/local/zephyr-sdk-0.17.0/arm-zephyr-eabi/bin...
Using nrfutil/dfu, I have previously flashed an older application+SD (s132_nrf52_3.0.0) onto the nRF52840 dongle.
Now, I cannot flash my newer application, since it contains...
Hi All,
Simply put I am trying to use the Xiao BLE Sense board connected to the Expansion board (with SD card slot) to write audio recorded data from the Xiao embedded PDM...
Hello, I'm programing my project while using the nrf52840 chip. I'm using segger embedded studio for the programming part because with the nrfconnect I have error code 9 ...
Hi I wish to integrate Matter over thread in unicast audio server . My objective is to use matter to control the volume and play/mute states. I would like to know whether...
Hello, checking if it's at all possible to have uart working on the nrf52832-dk using pins 18 and 21. I can get rx/tx working with an ftdi using pin 12 & 13, but not 18 &...
SETUP:
2 x NRF54L15 DK initiator/reflector sample (as of 4/8/2025) Major RTT settings below - RTT (BT_CONN_LE_CS_MAIN_MODE_1) with 1M phy, 32 bit random RTT (will add settings...
I am working with nrf52840 dongle, details on the antistatic cover are( nrf6829, 2.1.1, 2024.02). I am trying to flash it using https://github.com/adafruit/Adafruit_nRF52_Bootloader...
Hi all,
I'm facing a challenge with efficiently transmitting high-frequency sensor data over BLE.
I’m sampling sensor data via SPI from a sensor capable of outputting...
Dear Team,
I am attempting to provision my Thingy91 device to AWS IoT Core using Fleet Provisioning with the Claim method. I've been closely following the instructions in...
Hi everyone,
I'm experiencing an issue with my nRF54L15DK board.
When I build the OpenThread CLI sample with the /ns configuration, everything works as expected. However...
Hello, I am working with a Seeed XIAO nRF52840.
I'm able to get an average of 500 uA in SYSTEM OFF mode. However, for this application, the current consumption during wake...
Hi guys, With v2.8.0 sdk, L4_e3 code ( academy.nordicsemi.com/.../) works with nrf52833dk. We have a custom board that we designed. Here, nrf52820 chip is used. I can compile...
Hi,
I have thingy:53 and I have damage to the sw2 pin and I am unable to enter the DFU. I lost two tiny pieces that go just above the one in the photo and not even...
