Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
We are using nRF5340 with nRF7002 on our custom board. Our application requires:
Wi-Fi (via nRF7002)
Thread (via nRF5340)
DFU over Wi-Fi
We are concerned...
We have peripheral, and we want to connect it using NRF 52840. when we are bonding this using nrf connect app we get a pop up with random key and using pair we can pair with...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
in this example:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/conn_time_sync/README.html
the peripheral has this assert statement when...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
Hi
Is it possible and what is the correct way to implement main clock trimming at runtime? Which NCS version this works on?
I see there is already some setup going on...
Hi,
I want to write data to a specific memory. I understand there is ZMS.
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/fs/zms/README.html#zms...
Hi,
I am trying to build memfault sample as in intermediate course, after hello_world project configuration and prj.conf options addition, i get following build error...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
