Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hi there,
We have an Icarus IoT board, which uses an nRF9160 SiP. I am trying to get the nRF Cloud Multi Service sample to work. I am getting the following errors:
mqtt_connect...
Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Uploading via VSCode since version 3.0.0 (happened with the rc1 as well, Toolchain 3.0.0 and Toolchain 3.0.1) does not work for the nRF54L15DK (board rev 0.9.1 ENGB chip)...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board and a series of nrf52840dongles (provisioning and configuring inside the software and...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
I am working on a project using the nrf9160DK for initial firmware development. Trying out the SAADC i encountered that the measured values were always about 20% lower then...
Dear Nordic Team,
I hope this message finds you well. We are currently using the nRF9160 in our product and have a few questions:
Can you confirm the ongoing availability...
Hi, With this setup in , I successfully built a CIS mode using my nRF5340 DKs , enabling stereo sound while the microphone is active .
However, I am currently experiencing...
Hello,
I would like to ask how to update the appName field in the shadow register on the nRFCloud, using CoAP protocol.
I was able to change the appVersion by passing...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
