Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Dear DevZone,
I believe I am quite familiar to this forum due to my ongoing Wi-Fi issues with SDK 2.6.1 To determine if a newer SDK version will resolve these problems,...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
Hello everyone,
I'm having an issue with my nRF52840 Dongle. I can detect the device with nrfutil device list command, which shows:
> nrfutil device list DC1D9FD62EC5...
Hello Team,
I am trying to change the Lesson 9 Exercise 5 nrf5340_both_sol sample to use internal flash for FOTA. The code builds successfully. I have changed the pm_static...
Hi ,
I would like to use an external GPS active antenna on the nRF9151 EVB for testing (J2), does it disconnect the on board antenna GPS ? should I connect/disconnect any...
Trying to install NRF Command Line Tools. Platform is Linux 64bit x86 (distribution Ubuntu 22). I already have installed utilities by Segger, which may be the reason why NRF...
Question 1: I am using GPIO external interrupt. Does this interrupt belong to GPIOTE PORT EVENT by default? Question 2: How to configure low precision GPIOTE? Question 3:...
I use NCS2.5.0，and I noticed that there are two files(bluetooth.h and scan.h) can help to set scan parameters.Is there any difference betwen these two files?Can I call the...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi,
I am trying to optimize my nrf52840 application for power consumption. If I run simple loop using nrf5 SDK i get ~1.2mA. However with similiar code on Zephyr: I get...
Hi,
I am developing a small beacon application using the nRF 52805 device, and the intent is that it will send advertising packets at a slow rate, to indicate to a partner...
I'm working on implementing arithmetic operations using the PKA engine on the nrf52840 in Rust, following the CRYPTOCELL — Arm TrustZone CryptoCell 310 datasheet. While I...
Hello all,
I have been working on the implementation of the PKA engine on CC310, and have been encountering some unexpected behaviours when using the modular multiplication...
Hi,Nordic team
I am programming with nrf52833,ncs v2.9.0,base on peripheral_hids_keyboards and central_hids.
On central I call bt_hogp_rep_write_wo_rsp can only send one...
