I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hi,
I face a 3mA consumption while I have CONFIG_PM=y and wether or not I have CONFIG_PM_DEVICE=y.
The idle thread is reached and executed :
And the idle thread...
Hi,
Is there a way to make the main thread to execute after any interrupt?
For now, I have something like this (ncs 2.7.0):
in main thread :
In each IRQ handlers...
Hi,
I am sending 20 bytes of data in a beacon format. These are fit into m_beacon_info[2] to m_beacon_info[21] defined in ble_app_uart code from nordic SDK:
I send beacon...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hello All,
I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup,
https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. We have a project using the nrf52840, which is sometimes used by carriers. I ported radio_test to...
Hi
I am using HCI Power Control sample to dynamically control TX power. I found that the TX side's connection RSSI and RX side's are diferent, at some point it even has...
Hello, I'm trying to follow this example (Serial DFU) , on a nRF52840 custom board, but I'm getting the following error:
I couldn't find any relevant information and also...
Hi,
I have recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. To begin, I used the "Hello World" sample code. While I was able to successfully build...
I have searched everywhere and can't find a working example that shows how to create a new BLE ID and save it to the setting s partition.
Please show me the configurations...
I am incorporating the nrf52840 into a new design and it is my first time working with a Nordic product. I am looking to start with the SEGGER J-LINK EDU MINI due to it's...
Product: nRF54L15DK, SDK V2.9.0
Application: Multi protocol (BLE + Matter/Thread) Door Lock
Issue: BLE bonding is not retained after power cycles. The mobile app requests...
Hi,
I am debugging the zigbee functionality and would like to enable the zigbee log,already enabled log in prj.conf but no data coming out.What do I have to do to enable...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
hi Nordic teams:
we meet one serious issue about LSM6DSL FIFO reading, our product (host mcu is nrf52840) need to read lsm6dsl FIFO data periodically with one second interval...
