We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
hello,
I have in my current project which is already in production a few missing connection that I hope are not crucial.
I forgot to connect DEC2,DEC4 and DEC6 .
how...
I have a XIAO nrf52840 board . It has a button which does two things: one click seems to reboot the nrf52840 and double click enters bootloader mode. I'd like to override...
KConfig is warning me: CONFIG_LSM6DSO was assigned the value y, but got the value n. Missing dependencies: DT_HAS_ST_LSM6DSO_ENABLED
I am running on a custom board, the...
Hello,
I am testing nRF7002DK board using nRF Connect SDK.
Does nRF7002 support Wi-Fi roaming such as 802.11k, 802.11r, 802.11v?
If it supports Wi-Fi roaming, please...
Hello,
I have a question regarding the sys_poweroff() function. In my device, there is a mode where the board (including the nRF52840 chip and GPIOs) remains powered, but...
Hi,
I am developing an application with the nRF5340 microcontroller.
I need to use the I2C module, but if I insert the CONFIG_I2C=y configuration in my prj.conf file,...
When disconnecting and connecting BLE, if the J-Link debugger is connected, BLE_EVT_DISCONNECTED in ble_evt_handler is executed, but if the debugger is not connected and the...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi,
I have a custom nPM1100 borad and want to charge the battery. My schemetic shows here, I notice the battery cannot be charged. My shcemetic shows below:
I have confirmed...
Hi Support team,
I encountered some flash overflow errors when I enabled the MCUboot on nrf5340. Could I ask several questions?
My situations and requirements: 1. My project...
Dear Nordic Semiconductor Team,
We are very interested in your nRF7002DK development kit and are exploring its potential for use in an open-source IP camera project. Our...
Hi, I am using an two nrf5340 with hci_ipc enabled one acting as central and one as peripheral built on v2.9.0
The issue I am having is that the supervision timeout doesn...
We have a project with a device acting as a ble peripheral and a broadcast sink. First the ACL connection is set up and then it will scan for and sync to a broadcast with...
Hi,
With the attached code, the timer0_event_handler() is only called once - is there something else I need to do in the ISR or at initialisation-time to ensure that it...
Hi all! :)
I struggle to initialize GNSS when I don't have a connection with LTE. Examples that could be found on dev academy initializates GNNS after LTE has been initialized...
