But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello
Is is possible to change the UART pins dynamically? I am thinking to predefine the pins on device tree as follows:
&uart1 {
status = "okay" ;
current-speed...
1. Set up the development environment for the nRF52840 chip in VS Code, but encountered an issue where the chip could not be recognized. The development environment consists...
Hello,
I'm measuring current at the Vbmd jumper for the BMD-350 Eval Board. I'm able to measure 0.9uA running this code:
in the boot immediately after programming...
Hi,
We have experienced some unknown resets in our devices specifically when woken up after being in storage for a prolonged period in ULP mode - about a year or so. Afterwards...
Hello!
I'm writing an application that uses MQTT to post some sensor data to a server. My networking code is basically a duplicate of this sample , except I set up the LTE...
Hello -
I was nearing completion of a BLE Mesh project with the NRF52840 when there became a shortage of NRF52840 QFN. I decided to migrate back to the NRF52832 and reworked...
Hello, I’m testing a circuit built with the nPM1300. When connecting or disconnecting power via USB-C, noise is generated at the circuit's button, causing unintended signals...
I work currently working on a driver module supporting your nRF91x1. I schedule rx-operations via your nrf_modem_dect_phy_rx() dect_phy modem-api. I am using the .handle field...
Hi All,
I am exploring nrf54l15 which has rram 1524KB. However, noticed that not able to access beyond 1428KB.
When build sample hello world code found that only 1428KB...
I am currently trying to get LLEXTs to work on the nRF5340 Audio DK. I was able to compile an llext and load it successfully, using the cmake features, However, I would like...
I've testing out the GNSS and Location samples. According to documentation, A-GNSS is enabled by default in the location sample but I am not able to confirm this both through...
Good Afternoon,
I am working on getting the npm1300 up and running on my custom board. I have a 1v8 line and a 3v2 line with the load switches being used as LDOs. I am using...
Hi,
I'm working on an indoor positioning system using an nRF5340 and a CHW1010-ANT1 antenna array. I'm receiving IQ samples from BLE CTE packets and using them to calculate...
While using the nRF9151 DK , after inserting the onomondo sim and connecting, the Cellular Monitor SIM sections appears the Wireless Logic ICCID number instead of onomondo...
Hi,
We are developing a product with WIFI+BLE and we are using nRF7002DK as the base. The important function is OTA because our functions may be changed after the hardware...
