Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hello, I have an application running on an nRF9160. The current app was built using NCS 1.7.0 with the L2M2M Carrier Library enabled. I'm upgrading the application to use...
Hello,
We are developing a Cellular IoT device based on nRF9160 SiP. Essentially it is a battery powered temperature and humiduty sensor, that sends the measurement data...
Hello everyone,
we have an in-house HW with the nPM1300. Both load switches are configured as LDOs as described in datasheet chapter 9.3 configuration 1.
LDO1 is used...
Hi,
I have successfully implement the BLE video transfer using nrf70-wifi-ble-image-transfer-demo .
I can receive the image using the Android-Image-Transfer-Demo application...
I am using VSCode with SDK 2.9.1. I have added the spi21 to the device tree UI editor. When I choose the MOSI, MISO and SCLK, they all show up in the visual representation...
1. Our system is configured with circuit config3 of the nRF52833 WLCSP, where an external power supply of 1.8V is applied to VDD.
Power sequence : USB connection -> VBUS...
Hello,
I'm using the SLM application with an NRF9160. I'm sending AT commands for MQTT publish. After ~10hours the device reboots.
The setup AT commands from powerup...
Zephyr Version 3.7.99, Zeyphr SDK v0.17.0
Thread Version v1.4
Matter SDK Version 1.4
After the switch from Matter SDK version 1.3 to 1.4, the NVS module under Zephyr...
We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
Hi,
I need to use two or more different event lengths for different modes. The event length should be set based on the mode before establishing a connection. I found that...
I would like to know how to add an eSIM profile to an eSIM chip using the nRF9151 modem. Is there any platform or support that enables an infrastructure for this? What should...
Title: Issue with I2C (TWI) Communication on nRF52840 (SDK 16, Segger 8.2a)
Description:
I am working with the nRF52840 using nRF SDK 16 in Segger Embedded Studio 8...
Hi
is there an example for this: sending data over ISM band 2.4 gHz without BLE on a NRF52840 or similar?
I need to transmit 2 bytes board to board with jitter and delay...
Hello, I want to write an applicatin that gets at_coammnds from the terminal via uart, sends the command to the modem and then sends the respond back via uart. I have two...
