We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
nrf51822_sleep.txt
Currently i running nordic code in Arduino IDE through the library from RedbearLab : github.com/.../nRF51822-Arduino and I facing a problem in sleeping...
Hi, can anyone explain to me about this example in this link with details :
github.com/.../main.c
I'm a newbie in nordic and i found it difficult to understand this example...
I install
gcc-arm-none-eabi-4_9-2015q3-20150921-win32
make-3.81
coreutils-5.3.0
and setup the PATH in windows
then i enter CMD mode make some command to...
I am using the LFCLK RC oscillator, 8000ms calibration interval.
Is it possible to read from some register the resulting calibration value for the LFCLK RC oscillator?
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello,
measuring ADC signal on P0.26/AIN0/XL2 and P0.27/AIN1/XL1 doesn't work (I get constant value from the ADC not reflecting actual voltage on the pin). AIN2 - AIN7 seem...
I need to send a disconnect command from the app layer. I've seen a few other posts that say to use uint32_t sd_ble_gap_disconnect. One post had this line of code as an answer...
I am using the RBC mesh in a networking product using the nRF51422. We would like to turn the mesh on and off at selected times, say once per hour for a minute or two. I know...
Hey,
I have been trying to set up wdt for my application which services some interrupts once in a while and advertises continuously. I put the nrf to sleep using sd_app_evt_wait...
Hello,
I'm trying to read voltage signals from a sensor using internal ADC and send them OTA. For now, my codes seems to work, but the only problem with my codes is it...
I'm connecting my nrf51 with my phone and when I move far from the microcontroller (long distance) the connection is lost
what's the function witch rise this error and what...
the code of 51822 PAN 73# must be added in SDK 6.0?
/* Add workaround when starting timer2 */
*(uint32_t )0x4000AC0C = 1; //for Timer 2
NRF_TIMER2->TASKS_START = 1;
/...
hello there i want to interface nrf51 dk with ds3234 using spi. i see spi master example. how to assign SPI I/O pins. can you tell me how to do it?? i find SPIMO_SCK_PIN....
Hello,
I am trying to work with the nrf51sdkv10 and trying to install arm-gnu-gcc toolchain on my MAC-OSx (El-Capitan). I downloaded the 4.9.3 version and installed in the...
