Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I read somewhere that to get the callback working on pstorage write, read etc, you need to call pstorage_sys_event_handler() in a function set by softdevice_sys_evt_handler_set...
Hi,
Each Gazell device has unique address identifier (i.e. base address + prefix) mapped for each pipe. How about the host?
For example:
Device that transmits on pipe...
Hi,
Each Gazell Device has an unique address identifier (base address + prefixes), what is the default address identifier for the HOST?
For example
Gazell device transmits...
Hi,
I'm having trouble with how to begin debugging a hard fault error in my code. When I run the debugger, it always ends in the HardFault_Handler in arm_startup_nrf51.s...
I am developing a project by employing nRF51822 and my code is based on ble_app_uart. I met an issue that if there is no device connects to nRF51800 in 3 minutes, the program...
The nrf51 ARM Cortex-M0 processors, according to the documentation, are "code compatible with Cortex-M3". Does this mean they implement LDREX/STREX instructions for atomic...
Hei,
We would be using nrf52 chip in a very miniature device that should have both BLE and NFC capability. NFC is needed for just as a tag. Thus, nrf52 is a good option....
I moved from SDK 7 to SDK 9. I'm using timers with SDK7
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE, true);
err_code = app_timer_create...
I work with the IAR Workbench and the nRF52 and would like to enable the floating point unit. After installation of the MDK-8.1.0 and the check of the nrf52832_xxaa.i79 file...
Not able to access the corresponding On characteristic if having more than 1 service having this.
Noticed that the app always write to the last On characteristic instance...
I donwloaded and executed the nrf52 examples with Keil µVision as I use it everyday.
The problem is when I compile and use a BLE example, it is stuck in SVC handler.
The...
I have a problem to make a program that read e put a string in UART. In version 7 of sdk there are functions simple_uart_get() and simple_uart_putstring, but this functions...
In the examples\bsp\bsp.h file there is a typo on line 61:
#define BSP_APP_APP_TIMERS_NUMBER 0
It should be:
#define BSP_LED_APP_TIMERS_NUMBER 0
Where is the...
