I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Teaching myself the Nordic libraries and API for nRF51 - going smoothly.
Keil uV5 and Dongle and SDK 9.0.0
Wanted to send my own data in the characteristic for HRM service...
The workaround for nRF51822 PAN#73 specifies setting an undocumented register at offset 0x0C0C of the timer peripheral to 1 prior to TASKS_START , and clearing it after TASKS_STOP...
Hi
I am trying to flash a new firmware into my device through DFU via the programming python script.
I use SDK7.2.0, and do:
ipy main.py -f c:\myproject.hex -a XXXXXXXXXXXX...
We are using the Nordic UART service for our product. Should we just use the standard UUID that the Nordic Uart uses or just generate our own for the product?
Thanks
Hi,
I'm working on an embedded system using PAN1026 bluetooth. I want to use the nRF APP to communicate with the bluetooth module. Currently I have:
Setup the...
To support a mix of v2 and v3 chips, I want to use the 7.x SDK. But I'm not sure it's compatible. The matrix at infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
I'm trying to use the nRF52 preview DK from Linux. Could anyone provide the correct JLink commands for flashing both a standalone hex, as well as one with a softdevice?
...
I'm writing a build script for gcc for the nRF51 and I want to use the provided .ld scripts.
In SDK 8, those scripts were renamed from gcc_nrf51_XXX_xxab.ld to nrf51_xxab...
Hi,
I want read accel data from BNO055 sensor to NRF51 DK board, but SCL and SDA pins are 1 always.
My code is the next one:
#include "twi_master.h"
#include "twi_master_config...
I have existing design with I2C accelerometer on P0.1 and P0.2 (SDA/SCL). Don't need extreme data rates. Since examples of initializing on-board TWI don't seem to exist, and...
I am developing a tool that will be using the existing NRF51 dongle to run the S130 SD and it is being written in Python. There is no way to change any of these parameters...
Does anybody have a suggestion for a relatively low cost way to test the output power of a nRF24L01+ module? We make the modules (which are identical to the demo module) in...
Hi,
I am using the GPIOTE->PORT event to detect button presses and I would like to detect both button press and button release.
However, it seems like SENSE can only...
(this is duplicate with a support case I just opened... I hope that's okay.)
Hello, I am setting up a new laptop (our development machine caught a virus) and have installed...
