Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi,
we'd like to use nexus 7 II(android 5.1.1) to connect nrf51822, but cannot connect if nrf51822 uses whitelist.
step 1. we send advertising packets without using whitelist...
I'm trying to build our application using GNU Toolchain and currently facing compilation issue with __asm directive; the error thrown is:
../../NRF51_SDK_v6_1/nrf51822...
I usually see a system event "NRF_EVT_FLASH_OPERATION_ERROR" when updating my device firmware. SDK says that this event indicates that the ongoing flash operation has timed...
Hi, have anyone tested nrf51822 beacon smart kit on samsung tab 4? For some reasons it didn't detect the beacon. I have tested with company identifier of nordic, samsung and...
Since the IoT SDK is not support the IPSP Router role.
Is that mean the nRF51822 can't been used by other MCU which is running Contiki to become a Edge Router?
There are many links across the Internet to app note nAN-29 ( nRF51 Development with GCC and Eclipse ). In fact, I remember seeing a link to it on the Nordic website just...
Hi,
I am trying to test a UART bootloader with the hci_dfu_send_hex.py from SDK6.1.0
Unfortunately the script seems to crash, below is the output on the windows command...
Let's say I Have an nrf51822 on a small button cell battery having a sensor that is triggered on certain conditions.
What is the most efficient and power saving way to...
Hello. I'm using 24 MHz crystal to feed my MCU and not able to change it to 16 MHz to share with nrf24. Now I'm driving nrf24 XC1 with PWM signal 16 MHz and it works but not...
Hi,
We have NRF51822 chips programmed for specific application and it is working fine as BLE services etc.
In some scenarios, to debug we want to stream data from our...
device_manager_peripheral.c provided via Software Packs in Keil doesn't compile against S110 8.0.0 (or 8.1.0). Its version shows up as 1.1.1. Same thing happens with bsp.h...
By combining some examples, I'm starting to understand how the UART examples works.
Using Keil 8.0.0, and the PCA10003 Board, I'm trying to send a burst of messages over...
I can see and bond nrf51 with android, but with iPhone nothing.
What can i implement for see nrf51 with iPhone?
Can i pair Iphone and nrf51?
Sorry for the very bad english...
The new generation of nRF51822's have a few neat new features, particularly the automatic power management piece, that I would like to potentially leverage in our project...
Hello,
I'm seeing some 67.2kHz reference spurs on the RF signal when I'm turning on the constant carrier mode using the DTM interface on the nRF51822. Layout and circuit...
