I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
On the product page: www.nordicsemi.com/.../nRF-Connect-for-desktop
The link from the ' Documentation ' tab is: infocenter.nordicsemi.com/.../nRF_Connect_intro.html
...
Hi,
I have done BLE tutorials [BLE Advertising, Ble Services and BLE Characteristics]
With my NRF51-DK was working perfectly the example of BLE Characteristics (with...
Hi,
I designed a pcb using nrf51 chip with some sensors,
this pcb should read ,every minutes, all values from sensors and saves them into the flash memory beside that...
Dear
Now, I need make one nrf52832 board as USB Dongle, it can be HID device by checked from PC.
And, nrf52832 should support esb protocol, now for esb, I know something...
hai
i was started a bluetooth based project. So i have started with a blend micro.But the range of communication was very short.So i have chosen ble nano with TX power...
Hi
I am calculating the power consumption using
devzone.nordicsemi.com/.../
But there is some point that I don't understand.
When the BLE event type is "Peripheral...
Hello,
the past week I am trying to make the bootloader_secure example work for a custom hardware with no luck. This whole procedure give birth however to several questions...
Hi
I am currently working on a BLE based hardware but I am a little confused about the terms such as service, characteristics... etc.
Let's say, I would like to control...
Hi,
I am using the following function to read the content of a register:
static ret_code_t read_reg(uint8_t slave_address, uint8_t register_address, uint8_t *value)...
Hi,
Could you please help me identify the file and function name that is used by the S130 softdevice to start HF clock automatically for ble advertising? I can see that Clock...
Hello again,
I'm working with the ble_app_hrs example application with DFU app support. I'm following the DFU procedure and I've reached the point where I actually start...
Hi everyone,
My idea is:
I have several nrf51822 ble devices and I want to connect them simultaneously one by one with gateway over IOT. I am using bluz gateway shield...
hi all,
I use nRF52 SDK11 with ble_app_beacon example.And write some code in main().
uint8_t buf_data[32];
unsigned char c_data[] = {"abcd"};
//unsigned char c_data...
When debugging my application, I'm finding that gdb blocks at app_scheduler.c:253 like this:
(gdb) bt full
#0 0xfffffffe in ?? ()
No symbol table info available.
#1...
