Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
IAR ARM 7.60.2
Nrf52
Softdevice 132 v3.0
SDK 11
I am trying to use SPI with easy DMA. I have implemented the PAN 58 workaround for sending 1 byte but it fails...
I got started with bluetooth learning. But it's too hard to understand ble protocol. Do I have to learn BLE protocol even If my purpose is only ble communication with simple...
Hi,
Could someone help me about the following questions?
Q1: What are the connection parameters set by the Android app nRF Connect? Can I change them?
Q2: How can...
I have a bit of a strange problem.
I am designing a signal Gazell signal repeater.
It listens in host mode then sets itself as a device to pass the data along.
However...
Is it possible to put the nRF52 into recieve only mode (say through direct test mode) so that the input impedance can be measured using a VNA? Is the input impedance of the...
When I initialize PPI after timer1 has been initialized I get a fatal error (and reset).
Code:
const nrf_drv_timer_t timer1 = NRF_DRV_TIMER_INSTANCE(1);
nrf_ppi_channel_t...
Hello,
we were measuring sleep modes and it consumes around 1.3uA which is correct.
But when we needed to be woken up on edge we found out it consumes extra 8uA! Are you...
Are there any nRF51 demo firmware implementing paring function that the central and peripheral devices will connect automatically without user interaction when they come ...
i am working using NRF52, s132, sdk11, freertos.
for fft , i used "arm_rfft_fast_f32(...)" in cmsis-dsp library.
and i inserted a fpu interrupt.
NVIC_SetPriority...
Hi.
I'm using PCA10040.
I'm trying to control GPIO.
But I can't control PIN 09, 10.
Let me show you my source code.
int main(void)
{
/* Configure LED-pins as outputs...
Hello!
I have encountered an interesting issue:
When I use compiler flags (GCC CFLAGS) -Os or -O0 together with -flto the pstorage function pstorage_block_identifier_get...
After I combined the Timer example and ble_app_uart, the program is hanged at below function when init the timer. Please tell me why
__STATIC_INLINE void nrf_timer_event_clear...
I need to turn off a GPIO after 8 hours of it being triggered.
I was reading about changing the prescaler to allot for 8 hours. I did the calculations and came up with a...
