Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
I am trying to accomplish the following very simple task: use the broadcasting function of my nrf 8001 to send up to 19 Bytes of data over the air (connectionless).
I tried...
I need to create a backlight fade-in/out effect. For this I'm using the latest nrf_pwm lib form here together with the S110 Softdevice. Using the scheduler and an application...
Hi All,
We have been working on Arduino Mega board with BLE shield. We want to get the address of the BLE shield and we are using aci library for that.
I found this...
Hello,
Im using the master control panel app from nordic to use the DFU.
I can only once upload the application over DFU on my nRF51422. Because after the upload is...
Hi,
I have been trying to connect to a proximity tag and stay connected but with no luck. What happening is that the unit connect does its thing and then disconnect with...
I use a OLIMEX nRF8001 module with ATMEGA328 at 3v3. Using the "helloWorld" serial example sketch, I measure a current of approx 400-600uA. However, if I use the calculator...
Hi Nordic
I want to test parameter about output power 、sensitivity and so on ,but we have not software tool . Could you tell us how to test and provide tool to me .
...
Hi,
How to set user description descriptor to a particular attribute? I have created one primary gatt service with more than four characteristics, when is see it through...
Hi,
Master device is whole the time in receive mode and I have a problem with read data from device which address is in Pipe1. IRQ appear and status is 0x4e and FIFO status...
Hello, I bought the nRF51822 Development kit and the nRF6700 starter kit and I'm having trouble finding tutorials on how to use the 2.4 GHz radio mode on the nRF51822. Can...
Hi everyone,
I have some strange behavior with a central peripheral combination. My central subscribes notification on the peripheral. This has a limited TX-Buffer for just...
Hi,
I am developing the nRF51822 for the BLE device application. For the data delivery I am implement this function based on "button_radio_example(Tx/RX)" example code. It...
Hello,
I have been since many days desperately trying to set the bytes in the advertisement packets in my Arduino, combined with an NRF8001.
What I am trying to achieve...
Hi,
I would like to connect my msp430f1611 with NRF8001 bluetooth module and send data with an SPI communication. I found an interesting guide here with the main part of...
