Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi All,
A simple one,, I just downloaded the master control panel app for android in android 4.4 phone.
My question is how to do bonding and how to delete bonding info...
Hi All,
I am testing the functionality of NRF24L01+ and for my purposes I have configured it as PTX, No Auto ACK.
I am able to communicate with the chip just fine and...
I am trying to send continuously sampled analog input using NRF24LE1 using Shock burst,The transmitter is not working while trying sample continuously.please help.
code included...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I'm designing an application where both, BLE and Ant should / could be used. I tried to download the S310 SOFTDEVICE from www.nordicsemi.com/.../nRF51422 . I'm asked...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I need a low latency stereo digital streaming device and the model (nRF24Z1) is going to be discontinued.
Has Nordic a replacement for nRF24Z1?
PD: i need stereo, so...
In our product we have both a DFU profile and an application profile which is confusing Mac OS X 10.9 "Mavericks" since it caches device services unless it receives a service...
Hello,
I'm a new developer on nRF51822 and I'm trying to make a program that allows the nRF module to communicate with a glucose meter and a Smartphone application. My...
I'm working with the nrf51-app-ble-lbs demo from github. I notice that when I'm using BLE scanning apps, the VS service UUID is long (128 bits), whereas if I'm looking at...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi
I am new to embedded programming and I noticed that nrf51822 is a good and complete choice to start with both wireless and 32 bit arm programming.
However, I am not sure...
