Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hi,
I am trying to run nRFToolbox App, I imported the project to Android Studio but I get the following error when I attempt to run it:
Error:Execution failed for task...
I just switched over from SDK v6 to SDK v7.1 (installed via those Keil Packs). The UART has suddenly stopped working (via Segger USB COM port) and I can no longer see any...
Hi Nordic,
I used PIC32 for SPI Master and nRF51822 SPIS slave. I used shortcut for my spis in nRF51822 and I need to know the right time of acquiring the semaphore and...
I have a 32 byte string to read and write using SD110. In the MCP I can read (using read long) the whole string without any problems. When I try to use write long, MCP times...
I'm getting started with the ble_app_hrs_s110_pca10028 (nRF51 PCA10028) example in the nRF51_SDK_7.1.0_372d17a_packs.zip SDK. See the tags for my hardware setup. I'm using...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello ,I want to scan the Bluetooth peripherals through one master application and want to display the Bluetooth peripheral names on serial window like what master control...
I am new to nrf51822.
I am trying to convert my Arduino code into NRF51822
I need something like this
currentMillis = micros(); //microseconds since the Arduino board...
Hi,
Without dissecting the provided Raspberry Pi Debian packages -- is there a list of the required Linux kernel modules and binaries required for the IoT Dev Kit example...
Hi there. I'm currently trying to run the BLE_APP_HRS example from IAR workbench on nRF51822-Evaluation-Kit.
We are very interested in using this chip in our upcomming products...
Hi All,
I noticed CSR has just released something called CSR mesh, please see: http://www.csr.com/news/pr/2014/csr-mesh , and a demo video: http://www.youtube.com/watch...
I'm renewing my search for a point-to-multipoint radio system, preferably based on the nRF51822. Basically, I need to be able to connect up to 32 (or more!) nodes to a master...
I am trying to implement a mesh protocol using the nRF24L01+ transceiver.
After reading the product specification, I have concluded that the Enhanced ShockBurst cannot...
I'm working on a wireless sensor network and was thinking about using nRF51822 as the primary SoC. For my network it would primarily be low power sensors talking to one another...
