I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi, what I did is wrote below:
1/ I program the S120 softdevice to the nRF51822 board, using nRFgo studio software(the softdevice size is set to 80KB).
2/ I complied the...
Hello,
I recently tested the nRF51822 with a non-Nordic BLE devices and encountered some problems. When testing with Nordic the connection is maintained with no problem...
During testing I changed the device name in the DFU. After making the change the DFU client in the master control panel would no longer work.
Is it possible to make the...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi
I try to configure a ppi channel with timers to generate pwm signal
My entire code is working well without softdevice.
Here my ppi init function:
NRF_PPI->CH[0...
I am planning to build mobile devices that communicate directly between them with BLE. The devices are all the same and carried by users. users meet and exchange data. I can...
hi,all!
i am confused about whicn priority should i set for my interrupt.
For deteils, I need a gpioe interrupt for my button, and this button is used to POWER OFF my...
We wish to make a universal device that may used
for ANT with the nrf51422 and the 32kHz crystal.
or for BLE with the nrf51822 without the 32kHz crystal.
Will there be...
I'm trying to bring up a basic S120 application on PCA10001 based on the multilink central example, using the IAR toolchain.
I've programmed the S120 device using 1.0.0_3...
I'm developing a next generation device using nrf51822. To replicate existing behavior I'm trying to sniff the previous generation product behavior using the ble sniffer on...
Hello!
I am working with a NRF51822 and I need to change the address of pipes regularly (so I can use more than 8 NRF communicating together with ESB protocol).
My problem...
Hi,
I'm trying to understand if S120 soft device provides user configurable option for duplicate filtering of advertisement data. I couldn't find any info on the SoftDevice...
Hi,
I used the project gzll_ack_payload in nRF51 SDK for nRF51822, I changed the Device to send a packet per second, every thing goes OK with the default parameter.
...
Hi,
there is an example named gzll_ack_payload in the SDK of nrf51822.
when nrf51822 works in device mode, if a packet is send successfully, the funciton of nrf_gzll_device_tx_success...
