Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
I have device from another company that has a n51822 chip for BLE UART communication and it can send data to my phone via an app with no problems. However, I am having difficulty...
When I add an attribute with BLE_GAP_CONN_SEC_MODE_SET_OPEN I get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event when I try to read it.
I do not however get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
My application involves driving a digital-output (PDM) MEMS microphone at 1 -- 3.25 MHz with a clock generated on a GPIO.
devzone.nordicsemi.com/.../
The output of the...
Hi, I have a custom service with 3 characteristics and i've been attempting to send one of them as a notification so I can use it in the HRS sensor app by changing the UUIDs...
Hello,
I am working with the nRF51822 and S110 Softdevice. I have so far successfully created several examples of fairly complex Peripherals. Now I am trying to,
A)...
Hello,
If we use same hardware and antenna design of one of Nordic DV/EV kit, can we shorten bluetooth LE certification process?
I see Nordic points the following app...
Im trying to run the example blinky_example on BLENano (tried with gcc / nrf51822-sdk on linux and windows)
.hex from linux before merge : 8475 bytes
.hex from windows...
I'm looking at the downloads for the nRF51 DK which has the nRF51422 core. I'd like to put the s110 softdevice onto it, but I don't see a download for s110 on nrf51422, just...
Hello,
I am trying to use the s120\multilink_central example, using SDK v6.1 and S120 v2.0. The probleme is that I get a hardfault handler. I think that the probleme is...
Hi, I am using a nrf51822 with sdk 7.2.0 and s11o v7.1.0
I also have a imu ( mpu 6050 ) that gets accelerometer and gyroscope data.
How do I do continuous transmission...
Hi,
I am using the nRF51 Dongle and every time I send a command the pipeline goes into "Stall" condition. Using USBlyzer I can see that the command is sent but straight...
Hello,
I would like to build a device that looks for other beacons (not using a phone)... This device would simply look for other beacons near this device.
My questions...
I just tested putting the same firmware on two different nRF51822 s and inspected them with this test app .
They show two different UUID's.
I can find no macro...
Hello guys!
I'm experiencing some troubles trying to compile the blinky_rtx example for my new nrf51DK. The source is taken from the SDK7.2.0.
I'm under Linux and I...
