Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
I try to add an BLE function with "ble_stack_init". The problem is that after executing this function, the interrupt doesn't work (I add a function in the interrupt, but it...
Hi Nordic!
Long time short, I want to do an ANT application (S210, nRF51422) that pairs two slaves to one master. I have configured everything such that it pairs only when...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi Nordic,
We are trying to supply the chip nRF51422 with a Li-Ion battery. The nominal voltage is 3.7V, but as it is known, when full, this voltage can reach up to 4.2V...
Can the pc_ble_driver project located here be use in combination with SDK12?
We currently have it setup for SDK11 here, and want to upgrade to SDK12. We successfully built...
I want to develop a central role application (using a Redbear BLE Nano - based on nRF51)
I believe that this requires use of a softdevice and am looking for how to do this...
Hi. I am trying to set up timer in counter mode to count up signals from gpio through the ppi module, but it's not working. In main cycle I am testing the timer using led...
I want to sense bluetooth from any distance the radio can detect and without connecting, pairing or bonding. Simply turn led2 on while the nrf51822 senses RF and when it no...
For my application I need a lot of different timers. I dont use a soft device. Its a nRF52 Chip on board.
#define APP_TIMER_OP_QUEUE_SIZE 20
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Experimental Buttonless DFU worked correctly when compiled with keil, but the same example compiled in eclipse by gcc is not switching to bootloader mode. value 0x01 is updated...
Hi There,
Are timers 3 & 4 accessible to the application when using the v3.0 S132 softstack on the NRF52?
Looking at table 4 of S132_SDS_v3.0.pdf they are not listed.
Cheers...
Hi Community, many thanks for reading!
I have built a Breadboardadapter for an ISP1302
Inside
On Breadboard
There is no Groundplane or design rules.
Yes,...
I am using a nrf8001 and the arduino aci library ported to work with my project.
I have started from hello world example.
Connecting to the device from android app, sending...
