I am working on project using thenRF9151 board and I require the GNSS functionality to work for the same. However, my board is not able to latch on to a satellite network...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
I am running ble_uart_app in SDK_11 s130 on nRF51-dk
I am trying to detect certain pattern received in the UART Rx.
Here is my code.
void uart_event_handle(app_uart_evt_t...
I'm running SPI master (spi_master_tx_rx) at 4MHz for multi byte burst reads. As seen in the attached screenshot there are 5.5µs delays between the bytes. The delays increase...
hello there ,I am writing spi code for slave which has 19 bytes of data. my nrf51 is master.
now my slave has clock polarity =1, clock phase =1. i am uploading project...
Hi All,
I'm trying to test the ble_app_hrs_rscs_relay example on an nRF51822 (256 Ko flash / 16 Ko RAM) with the softdevice s130 but unfortunately the program is not being...
I am using ble_uart_app on SDK_11 nRF51-dk s130.
I would like to send binary hex data instead of ASCII. Looking at ble_nus_string_send(), it seems that sending binary hex...
Hi ,
Recently started working on nRF52832 and tried implementing its various applications for NFC, which includes URL, android application, name tags. Can anyone suggest...
As part of some testing, I downloaded some wrong files and seem to have contaminated the default boot files. So now when I try to download the NORDIC hex files, i get an error...
Hi ,
We are using NRF52, S132 softdevice ... Whenever we do hard reset everything works fine .. But if I do flash from my IDE (using eclipse,this is a soft reset) and it...
I have a hard time to initial a twi ,I reference the example in the SDK11.0，and I used the board is 10040,I copy the example twi sensor code in my project ,but there is an...
I'm getting the error code 0x4001 from sd_clock_hfclk_request and I can't find where the error codes are defined/explained for this function. Can someone point me in the right...
Hi,
With the following program running, how can I achieve the lowest power consumption between timer events:
nRF Timer is running with the HF crystal requested
...
51822, config a pin as output , in the param , set disconnect or connect the input pin, when config as output ,what mean disconnct/connect input pin?
I use a pin to light...
For my project to simulate the spreading of a disease I am thinking of recording the complete social network on the beacons and then collecting the data to a pc. I have roughly...
I am using nRF51-DK hardware and working on the ble_uart_app s130 SDK_11
Upon power-up, nRF51 is discoverable and connectable. After sometime, it is no longer discoverable...
