Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hi,
Is it possible to use SPI master on nrf51822 in 9bit mode or shall I use bitbanging?
I have a slave (SSD1306) that accepts only 9bit words.
Thanks,
Sergey
I'm trying to DFU the softdevice (supplied 7.0 hex file) using bootloader example in SDK 6.0. I wrote my own OSX application to do that by parsing the hex file and sending...
i need to display my scanned response data in android application along with the device address.for displaying the device address getaddress()function is there in android...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
I added a way to go from a running application into DFU mode using a custom characteristic and GPRETEG. However, CoreBluetooth caches services and characteristics for each...
Hi all,
I'm designing my own breakout board for nrf51822 and want to use the mbed platform for it. I was able to make the board work with a very simple, blinking-LED program...
Hello,
I am a newbie of Bluetooth development. I have a question that what is the difference between ACI (Application Controller Interface) given in nRF 8001 and HCI (Host...
Hello,
I have one Eval-Kit (v2.2.0) and I had no problems with SDK5.2.0 and demo programs defined in nRF51822 Evaluation Kit User Guide v1.2. Now I have installed SDK6...
Hi,
On a nRF51822 (QFAAG0) with S120 softdevice (using the recent PCA 10001 v2.2.0 board), i'm trying to perform these operations successively:
a simple RSSI scan...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I want to use the AES of 51822 and I have read the nRF51_Reference_manual,I cann't find any demo about AES in SDK.Do you have the demo code about 51822 AES encryption...
Help please! I've been using the nrf51822-EK for several months. Everything has been working well.
I updated my SDK in order to be compatible with S110-SD-v6. Everything...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
am using nrf51822 chip communicating with PIC16fl1509 through uart.the PIC will send the temperatire values through uart to nrf51822. i have a doubt ! will the uart communication...
