Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Please find attached the screenshot of the schematic where i have combined the RF circuitry from
the NRF52 DK and the NRF51822 dongle for a compact board development. . ...
Hello,
Can anyone tell me if it possible to have one peripheral device connected to 2 central devices ? I am using S132 softdevice with nRF52832 board.
Thank you !
nrf51connect.pcapng nrf52disconnect.pcapng Hi i m using pi3 with bluez and the gatttool i can easy connect to the Adafruit Feather M0 with a nrf51 as bluetooth module but...
Hello,
my program should do the following:
Collect sensor data
Initialize SD and start advertising
After a timeout or after a successful data connection it...
Hi, Nordic
I want to change usb in/out packet size after hal_usb_init().
as I know, it should make one report descriptor and update.
But I can not see similar demo...
My latest assignment is adding NFC functionality to the device (the very same device that I had trouble with DFU on). Adding the functionality was easy enough but I'm having...
I have seen this topic:
devzone.nordicsemi.com/.../
and a few others, in an attempt to visualize the RAM usage of my project. I currently use GNU ARM Embedded (gcc)...
Please clarify the radio state diagram for the nRF52: it shows a black dot between TXIDLE and RXIDLE states, having arrows from TXIDLE or RXIDLE leading apparently back to...
Hi guys!
I wanted to ask that can we use an external flash(connected via SPI/I2C interface to the mcu) instead of internal flash for storing downloaded image(s)?...
Background: We use NRF52 chip along with SDK 12.1.0. Since we have a few components of firmware (i.e. secure DFU settings, secure DFU , application, Softdevice) that go into...
The aim is to use the nRF51822 chip beside the application processor and to run the soft device S130 in it but as I saw, the newest SDK v12 supports only S132 Connectivity...
I am trying to update my S132v2.0.1 devices over the air to S132v3.0.0 and am getting no bootup, even after swapping dfu_dual_bank.c from the answer below.
devzone.nordicsemi...
I am studying this tutorial: nRF52 Online Power Profiler . I know this tutorial basically related to the ble_app_pwr_profiling example in the SDK: Power Profiling Application...
Hi, Nordic
I know pipe0 and pipe1 are be enabled on nRF24LU1 nRFgo SDK example for default PRX.
Now I only to enable pipe0, disable pipe1.
First, I use this...
Hi, Nordic engineer
nRF52832 as ESB PTX, nRF24LU1 as ESB PRX
same channel, crc, and match address and pipes, but from nRF52832 uart log, ESB TX fail event always show...
