Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Good day everyone,
I would like to utilise the nRF52832 BLE chip in an application that requires radio communication between a master and slave. The slave needs to be powered...
Hi everyone,
I am using LPCOMP in rFF58122.
When coosing the reference voltage, I have to fill the structure nrf_drv_lpcomp_config_t with the hal nrf_lpcomp_config_t that...
Hello, I try to add TWI function in my project (uVision5) so I add this modules with 'Manage Run-time Environement':
nrf_drv_twi
nrf_twi
app_twi
and I get...
hi
I have a problem in integrating a 1.8V GSM modem with nRF52832 through UART. nRF52832 supplied with 3.3V and there is a voltage divider that covert 3.3V to 1.8V in the...
hello....
Nrf 52832 does not work.
With a newly developed board,
Programming with nrfgo studio and J-link is not possible.
It feels like it does not have a good reset...
I'm looking for an example code of central role which can run on nRF52 DK.
I want to check if it is possible for nRF52 DK to send a LL_CONNECTION_UPDATE_REQ PDU to slave...
In general, I'm working on my own dfu-bootloader project which was developped on the "Engineering A" chip-revision of the nRF52832. We finally have new hardware with the chip...
Hi all,
I have use nRF5_SDK_11.0.0_89a8197 and S130 before and use nRF Toolbox to do switch it to bootloader and do OTA, just use one APP. However, now I'm using nRF5_SDK_12...
Hi,
I look at this demo,found that the ESB is PRX in most time, it may lead to a high power consumption.I want to achieve auto ack, piggybacking data in ACk from PRX.So the...
Hi all, I'm working on experimental_ble_app_buttonless_dfu project in sdk13-alpha using pca10040 board. I just compiled experimental_ble_app_buttonless_dfu successfully for...
Hello all,
I am implementing an energy efficient system, in which I am advertising in BLE_GAP_ADV_TYPE_ADV_SCAN_IND mode, I am using scan_req_report as an acknowledgement...
I'm trying to following example of nRF51_SDK_v12 OTA-DFU Example , but there are no support with BLE400 at all. (BLE 400 has nrf51822 QFACA1 1536EK Chip on it)
I think...
Hi Nordic Team,
Please I would like to ask how can I globally identify my device (nRF51822) based on its address?
Assuming that:
The address type of nRF51 is...
Hi all,
Is it possible to place your own antenna into nrf51822 bluetooth smart beacon kit? if it's possible, how am i going to do it?
am i suppose to remove the antenna...
I made a custom BLE device using nrf51822 and need to do DFU from remote place.
The BLE device is connected using USB to windows PC.
The Serial bootloader examples are...
