Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
SDK: nRF5 SDK
Board: nRF52810
Softdevice: S112
Hi,
I have a board that has two TWI lines, one has two peripherals and the other has one peripheral connected to nrf52810...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I asked a question earlier related to this here:
But I want to make sure I have understood this correctly, and check nothing has changed.
From my understanding, the...
Bonjour, J'ai récemment eu le besoin d'ajouter le bluetooth dans un de mes projet et j'ai opté pour le BL54L15 de chez Ezurio que je programme avec une nRF54L15-DK. Mon soucis...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
Hello,
I am developing using VSCode on Windows. When I use the "Build" button from the NCS option list (see first image) I get the build output without any colors. When...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
I currently have an nrf9151dk set up on a breadboard along with some peripherals intended for some evaluative testing. Part of the purpose of this testing is to assess the...
Hi,
We are looking to test the Skylo NTN network with the nrf9151.
We have NTN sim cards from Monogoto.
Do we need to load any special modem firmware to the chip? The...
