Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
I have having following configuration:
I want a fail safe method to update firmware on nrf51822 using attached host controller. I looked at serial wire debug interface...
Hello,
I'm running a serialized application based on the SDK 10 and S130 v1 and I am in the process of porting the peer manager to the application µC.
Due to the fact...
I'm trying to set up a system where the sample rate of data being notified to the client from various sensors can be changed by updating a configuration characteristic in...
Hi all,
I have one nRF52 DK board (PCA10040), and I have installed necessary JLINK drivers when first connecting the board to PC, it can displays the virtual COM port correctly...
I have a board here with nrf52832 rev B attached to a max98089 i2s codec. In this application we are only really using the ADC channel of the codec. Everything is configured...
Hi NordicS
Do you have a code example for a central UART application?
I am looking for a example that acts just like the nRF Uart App, but running on e.g. a PCA10031...
Is there a way to resolve a private resolvable address on connection? I have all the bonding information, IRKs etc, from everything which I'm bonded with, I'd like to work...
Hi.
I'm currently trying to scan beacons with timeslot example.
However, I found that there're more than 20% of loss while scanning beacons broadcast.
I think that...
Hi all,
I have one PCA10040 board, and want to start to download and run some examples while reading the on-line documentations.
In section "Running precompiled examples...
Hi,
I'm attempting to use the UART in a high speed configuration without flow control but I get regularely get two kinds of errors in the output:
Lost characters...
Our customer Farho is using the nRF905 transceiver a long time ago in their heater systems.
Now they have a project where they need to establish the communication with...
Hi everyone ,
I am working on button and pwm function by using timer ,whenever i press the button for 3 sec and pwm pulse signal is getting generated followed by pressing...
Hi,
I want to evaluate communication between several NRF51 chips using ANT. I could just buy a bunch of NRF51 DK kits but that seems pretty expensive.
What is the best...
Hi. I have the following code which runs perfectly on several C IDEs ( including Eclipse, Dev-C++, Code:Blocks and on the Linux Terminal using gcc as well ). However, when...
Hi,
I am an iOS developer trying to implement the app for an nrf51822 chip-based device. I am trying to perform DFU of application type using the objective-C files from...
