board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Are there any code examples available that show how to use the ram retention while shutting down the processor to it's lowest power consumption mode? Also does anyone have...
Hi,
I am currently designing a PCB to accept the BGA version of the nrf51822.
The Altium reference designs for the CEAA package (BGA) all include vias directly in the...
Hi,
We have a hardware application that prevents us from using flow control to interface with external hardware. We require the NRF51822 to be able to buffer up to 256...
I have a working design on the nRF51822 Evaluation Kit, and I now need to port that into a module that sits on a custom board. Any recommendations for making this process...
Could someone can tell me what is the difference between BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME? I tried BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME
advertisement...
I am trying to figure out how interrupts are set up for say a sensor with an interrupt line which signals when new data is ready.
I am assuming you set up a GPIOTE somehow...
I have been looking at the NRF51822 for data logging sensor measurements from the ADC. Currently, I have run into some limitations with iOS and can only get approximately...
Hello,
Its me again.First of all I want to say thanks to HÅKON ALSETH, with his help I was able to work with hardware interrrupt. now I am facing another problem, I need...
want to FLASH upgrade FW in the nRF51822 though my application controller. Is C or C++ code available for this operation or can you deliver a protocol description how to setup...
Hello Everybody,
I am new to Nordic and Bluetooth. I see nrf51822a have BLE + Cortex MCU inbuilt and this suits best to my application.
I have some doubts regarding...
How do I use nRF51822DK without "nRFgo Starter Kit Motherboard"? I have read "nRF51822 Development Kit User Guide v1.2" and have no result how can I only use nRF51822DK hardware...
Dear All
i would like to use
nRF51822
nRF51422
i would like to use nordic product,
but so shame, too low basic knowledge for make program for embedded, edit library...
Hello,
I attached the schematic found in the manual for NRF8001, in the case of DC/DC converter enabled.
It shows that an external 32.768KHZ crystal is used, while in...
Hello, I have major problem trying to debug/run ble_app_hrs example. The thing is that when I enter debug mode the code is stuck here:
0x000001B4 4908 LDR r1,[pc,#32...
