Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi all,
It is a common convention to configure the I2C SCL signal to be push-pull instead of open-collector if there are no other I2C masters in the system (saves a pull...
NRF52840
S140
App based on ble_app_multilink_central.
I have tried to build a bridge between BLE peripheral and PC.
I have spend so many time on PC side app.
The...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
Hi! I am designing a nRF54 based motion tracker that has an IMU onboard which can take an external clock signal for improved timing accuracy. Initially I had thought of just...
Hello,
I am having an issue using GPIO P0.03 as a button input in my design. Unfortunately, I did not notice that this pin is marked as a dedicated pin for the GRTC peripheral...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hi! It seems that I may have uploaded a non-working application to the Thingy91x. Therefore Device is not conectable via USB. The device is responding only in "MCUBOOT" mode...
Hello all, I am writing this as I am very new to Studio visual code, nrf connect, and many various things used in this project. Currently I am using the two samples given...
dear all,
We are fighting with a problem that defied every effort to solve it so far, so we are asking for help. Our custom board is based on the nrf5340 SoC connected via...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi, I have created my own hardware with nRF54L15 – 2xLED, 2xPWM, and Radio (BLE). I am trying to create a custom board using the graphical wizard. LED and PWM seems to work...
Hello,
I am using nRF5340 DK, I was trying to connect it to my laptop MacBook Pro M2 but I continuously get this notifications about JLink disconnecting and reconnecting...
Hi
I have a project developed on the nrf52840dk / nrf52840 dongle and am trying to build it for the Laird BL654 dongle. The build fails due to a missing 'runners.yaml' file...
