Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hi All,
We are in design phase of our project, which uses two NRF52 chipset one as master and Central , We have some prewritten content in Flash, which need to be read...
I ´m testing gpiote interrupt, i´m work with nrf51-dk, softdevice S110 and sdk 9.0.0.
I have a pin that receives a signal 0 all time, and it changes to 1 when I have to...
Hi, I'm using SDK 7.2 and S110 7.1.
I haven't mirgrated to SDK 10 yet.
I'm using the HRS and bootloader (which uses dual bank and BLE OTA) example.
After I select...
I am using nRF51 with Softdevice S110 to do a BLE peripheral, I want to have pin-code authentication before central device (or android phone) can connect to the peripheral...
ble_app_hrs_rscs_relay.hex the application ble_app_hrs_rscs_relay in SDK v9 can run fine,but in SDK v10.0.0 it doesnt work,even when i debug , it cannot go to main, and i...
Hi.
I have troubles.
I'm using nRF52 DK and V0.9.0.
I'm making program that does TWI communication between MPU9250 what is 9-axis sensor.
error is false every time.
...
I'm having problems getting the DFU dual bank ble s110 example to work on my target. My custom BLE app on my target is running fine, so my hardware is all good, and the DFU...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
I'm using s132_nrf52_2.0.0-7.alpha_softdevice. I've verified that the soft device is enabled.
void rdi_set_gap_parameters(void)
{
uint32_t err_code;
ble_gap_conn_params_t...
Is there are working example of FreeRTOS running on the nRF52 using the S132 SoftDevice? I am trying to get a ble_hrs example running with a updated version of the FreeRTOS...
Hi,
We have a rev3 nrf51822 system running S110 v7.3 and using SDK6.1.0. We are having trouble tracking down a ~1mA baseline current consumption when in system on/low power...
I'm struggling to understand this strange issue. I have a firmware based on S110 SD on nRf51822-QFABA0, this firmware is still based on version 7.1.0. The application is based...
I'm working on a program which sends 20 kb of data (sending 16 byte at a time) with one condition which is that indication should be enabled first. the first function checks...
