I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I'm looking to design power management circuit for a 3.7V Li rechargeable battery powered wearable sensor design. Any such reference design would be greatly helpful!
Thank...
I'm developing a device that's supposed to establish an encrypted connection with an Android device and I've gotten PM_CONN_SEC_ERROR_PIN_OR_KEY_MISSING during connecting...
I have the Type 4 Tag sample application running and I can read and write the tag without any problems.
I'm getting a little confused reading through the sample application...
Hello,
I am working with the GPIO tasks and events feature on my nRF52832 DK. And I noticed some strange behaviour. I want that two Pins will toggle if some timer events...
Hi,
Please help me with the following theoretical situation:
I have a NRF52832 running HID profile, mostly sleeping.
From time to time, an external interrupt occur (GPIO...
Hi,
I am trying to get the data written from a central (a smartphone in my case) to one of the characteristic of my peripheral using write request. The problem is that...
Dear developers,
We had a working application with SDK11 SD2.0.1 that we have migrated to SDK12 SD3.0.0. With SDK11 we could successfully bond to multiple peripherals and...
Hi. I use the nRF51882 and Arduino ide for developing. My main goal is turn on and off the Led thru the Bluetooth interface. But when I use the UART service for it I have...
I am seemingly haunted by spurious 'soft resets' I cannot seem to find a good explanation.
I have an application that is to be dormant until activated. When waking up I...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi, Nordic
I download SDK13.0.0-1.alpha_055eef3, open project
\gzll\experimental\gzp_dynamic_pairing\device\pca10040\blank\arm5_no_packs\gzll_dynamic_pairing_device_pca10040...
Is there any example of changing the default mtu size of 23 to a bigger value?
We tried increasing the att_mtu to 512, and reserved more ram for the softdevice, but still...
I have a rather unique problem. I want to control an "old-fashioned" DPDT relay using nRF52 GPIO lines. I'm trying to accomplish this task without adding a power transistor...
Hi all,
there is a nice section in here already about enabling the Reset input (P0.21). Unfortunately the link to the relevant infocenter docu is missing.
Could you...
